沥青泵-沥青泵厂家-沥青泵报价-沥青泵检修有哪些误区-鸿海泵业

1、环密封圈越紧越好。沥青 泵静环密封圈基本处于静止状态，相对较紧密封效果会好些，但过紧也是有害的。
一是引起静环密封因过热变形，影响密封效果;二是静环材质以石墨居多.一般较脆，过度受力极易引起碎裂;三是安装、拆卸困难，极易损坏静环。
2、新的比旧的好。相对而言沥青泵使用新机械密封的效果好于旧的，但新机械密封的质量或材质选择不当时，配合尺寸误差较大会影响密封效果：在聚合性和渗透性介质中，静环如无过度磨损，还是不更换为好。因为静环在静环座中长时间处于静止状态，使聚合物和杂质沉积为一体.起到了较好的密封作用。
3、静拆修总比不拆好，沥青泵一旦出现机械密封泄漏便急于拆修。其实，有时密封并没有损坏，只需调整工况或适当调整密封就可消除泄漏。这样既避免浪费又可以验证自己的故障判断能力，积累维修经验提高检修质量。
4、叶轮锁母越紧越好。沥青泵机械密封泄漏中，轴套与轴之间的泄漏(轴间泄漏)是比较常见的，一般认为，轴问泄漏就是叶轮锁母没锁紧，其买导致轴间泄漏的因素较多、如轴间垫失效，偏移，轴问内有杂质，轴与轴套配合处有较大的形位误差，接触面破坏.轴上各部件间有间隙;轴头螺纹过长等都会导致轴间泄漏。锁母锁紧过度只会导致轴间垫过早失效，相反适度锁紧锁母，使轴问垫始终保持一疋的压缩弹性，在运转中锁母会自动适时锁紧，使轴间始终处于良好的密封状态。
5、动环密封圈越紧越好，其实动环密封圈过紧有害无益。一是加剧密封圈与轴套间的磨损泄漏;二是增大了动环轴向调整、移动的阻力、在工况变化频繁时无法适时进行调整;三是弹簧过度疲劳易损坏：四是使动环密封圈变形、影响密封效果。
6、弹簧压缩量越大密封效果越好。其买不然，弹簧压缩量过大，可导致摩擦副急剧磨损，瞬间烧损;过度的压缩使弹簧失去调节动环端面的能力，导致密封失效。

1, ring ring more compactly as possible. Asphalt pump static seal ring is basically in a static state, the relatively tight seal effect will be better, but too tight is harmful.
One is caused by static seal due to overheating, the impact of sealing effect; two static ring materials are mostly of graphite, are generally more brittle, vulnerableto excessive stress caused by fragmentation; three is installed, the removal of difficulties, easily damaged static ring.
2, the new better than old. Relatively new asphalt pump mechanical seal better than the old, but the quality of the new mechanical seal or choice of materials is not the time, with the larger size of the error will affect the seal: and permeability in the polymerization medium, such as static ring without excessive wear, or not replaced at all. Because the static ring in a static ring seat in a long time in the stationary state, so that deposition of polymers and impurities as a whole. Played a good sealing effect.
3, static demolition demolition than never good repair, asphalt pump once the mechanical seal leakage will be eager to overhaul. In fact, sometimes closed and not broken, just adjust the operation or the appropriate adjustments can be sealed to eliminate leakage. This can not only avoid wasteful and can verify their ability to judge the fault repair experience accumulation, improve the quality of maintenance.
4, the impeller lock nut tightening the better. Mechanical asphalt pump seal leakage, leakage between the sleeve and the shaft (inter axis leakage) is relatively common, generally, shaft impeller leakage is asked not the lock master lock, the buy in the shaft, such as more leakage factor axis pad failure, migration, shaft ask inside the impurities, shaft and sleeve with a larger form bit error, contact surface damage. Shaft gap between the parts; head thread is too long will cause inter axis leakage. Lock home lock will only lead to excessive axle pad premature failure, instead of moderate locking mother, so that axis asked pad remains elastic one piece, a lock nut in operation will automatically lock the right time, so that the axis is always in good sealing state.
5, ring ring tightening the better, in fact, dynamic tight ring seals harmful. One is the severe wear of sealing ring and sleeve leakage; two is to increase the dynamic axial adjustment of the resistance movement, the frequent changes in working conditions, unable to make timely adjustments; three spring fatigue is easy to damage: four ring seal is dynamic deformation, the impact of sealing effect.
6, the greater amount of spring compression seal effect. Buy otherwise, excessive compression spring, can lead to rapid wear of friction pairs, instantaneous burning; excessive compression spring lose their ability to adjust ring face, resulting in seal failure.